Cyclades AlterPath BladeManager Instrukcja Obsługi Strona 76
- Strona / 240
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
62 MergePoint 5224/5240 Service Processor Manager Installer and Administrator Guide
6. Click OK. The security profile confirmation screen appears.
7. Click Save and apply changes.
8. Click Next, if desired, to go to the next Wizard screen.
Configuring Network Interfaces in the Wizard
By selecting the Network interfaces option from the Wizard menu, the administrative user can
configure network interfaces and Ethernet ports. See Configuring failover on page 62 and
Configuring primary and secondary Ethernet ports on page 62 for more information. Table 4.11 on
page 40 shows the values to use when configuring network interfaces.
Clicking the Next button on the Network Interfaces screen brings up one of two screens for
configuring the Ethernet ports, depending on whether failover is enabled or disabled. Table 4.12 on
page 41 shows the values to use when configuring Ethernet ports.
Configuring routes
Configuring the network interfaces in either of the two following ways sets up a default route for
the SP manager:
•When the DHCP checkbox is checked on any of the network interface screens, the DHCP
server assigns the SP manager a default route.
•If the DHCP checkbox is not checked, the gateway IP specified by the administrative user in
the Gateway IP field is used to create a default route for the interface.
If a host or network route is required, the administrative user should select Network
- Static routes
to configure the route.
Configuring failover
If failover is enabled on the Network Interfaces screen, clicking the Next button brings up a screen
for configuring the failover device. Clicking the Next button brings up the subnet
configuration screen.
With failover enabled, the secondary Ethernet interface becomes bonded to the primary Ethernet
interface, and the secondary Ethernet interface becomes active only if the primary Ethernet port is
not available. As a result, the values entered in the fields on the failover configuration screen apply
to the single bond0 interface.
Configuring primary and secondary Ethernet ports
If failover is disabled, the administrative user can configure each Ethernet port separately in the
following ways:
• Enable or disable each Ethernet port
• Enable or disable DHCP
• If DHCP is disabled, configure each port for static IP addressing
- MergePoint™ 1
- 5224/5240 1
- USA Notification 2
- Canadian Notification 2
- MergePoint™ 5224/5240 3
- Service Processor Manager 3
- Table of Contents 5
- Table of Contents v 7
- List of Figures 11
- List of Tables 13
- Installation Introduction 15
- MERGEPOINT 16
- Modem Types and Options 18
- Power Management Unit Options 18
- -tilt bar 19
- Basic Installation Procedures 21
- Connecting Devices 24
- Advanced Installation Topics 31
- Telephone 32
- Administration Introduction 35
- SP Manager 38
- User and Group Configuration 39
- Security Profiles 39
- Services 41
- Telnet service configuration 42
- Telnet client configuration 42
- DHCP client 42
- DHCP server 43
- IPSec VPN connections 48
- PPTP VPN connections 50
- Manager 52
- Syslog servers 53
- Private Ethernet ports 53
- Public Ethernet ports 53
- Failover 53
- Ethernet media configuration 54
- Dial-in and Callback Access 55
- Power Management Options 57
- Target Device Configuration 59
- 5224/5240 SP Manager 64
- -in chains 69
- Using the Web Manager 71
- Dialogs in the Web Manager 73
- Web Manager Wizard 74
- Configuring routes 76
- Configuring failover 76
- Upgrading IPDU Software 82
- Configuring the AUX Port 83
- - AUX Port menu option 84
- Configuring PC Cards 86
- -down menu on the PCMCIA 88
- -down menu on the 88
- - Date/time menu option 88
- Local boot options 89
- Network boot options 90
- Configuring Outbound Email 91
- # gunzip 92
- Configuring Target Devices 93
- Configuring Users and Groups 95
- Configuring Device Groups 97
- - Authentication menu option 100
- -down menu 100
- 5240 SP Manager 104
- Configuring Notifications 104
- - Notifications menu option 105
- -down menu. If the 105
- Configuring Sensor Alarms 107
- Configuring SNMP 110
- - SNMP menu option 113
- - Host settings menu option 115
- Configuring Hosts 117
- Configuring Static Routes 118
- Configuring VPN Connections 118
- Viewing System Information 121
- - Product upgrades 123
- - Restart menu option 124
- Administration Tasks Not 125
- Performed in the Web Manager 125
- -mounted directory 128
- -t ext2 /dev/hdc1 /mnt/opie/) 128
- -in or Telnet connection: 131
- Configuring the DHCP Server 134
- -q priv0" 136
- -ins Using cli 136
- -flow type to both 137
- -flow both 137
- Configuring Routes With cli 141
- Saving Configuration Changes 142
- saveconf 143
- MergePoint5224 login: root 145
- Password: password 145
- -out] [retries] 150
- Using the cli Utility 157
- Interactive mode 158
- Batch mode 158
- Autocompletion 162
- Enter> 163
- Parameters that can be added 165
- -source <IPaddress>] 174
- Default: no setting 178
- Appendices 179
- Login failure 180
- Web manager stops responding 181
- Firmware image is corrupted 181
- Target device types 183
- Appendices 171 185
- Appendices 173 187
- Using the sptemplate utility 188
- Appendices 179 193
- Appendices 181 195
- Why define private subnets? 196
- Configuring a private subnet 197
- Appendices 189 203
- Appendices 191 205
- Appendices 193 207
- IP: 192.168.4.22 208
- Appendices 195 209
- Appendices 199 213
- Boot file location 214
- Changing the boot image 216
- <N> completed 219
- Appendix E: Technical Support 222
- Numerics 223
- Index 211 225
- Index 213 227
- Index 215 229
- Index 217 231
- Index 219 233
- Index 221 235
- Index 223 237
Powiązane produkty i podręczniki dla Serwery Cyclades AlterPath BladeManager
(202 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji